Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
AfterTrusted Gate Installation for San Fernando Homeowners
our Gate Installation in San Fernando typically costs between $2,800 and $9,500 depending on the gate type, material, motor selection, and site prep. Most standard single-swing driveway gates with automation run $3,200 to $5,800 installed, and we quote the full price in writing before a single tool comes off the truck. That written-price habit comes from Adrian Vance’s commercial access-control background, where an undocumented verbal estimate was never an acceptable way to start a job.
We’ve installed and repaired more than 22,000 gates since 2014, and every one of those jobs left with a photographed record of what was found, what was set, and what was installed. If you’re in San Fernando and need a new driveway gate, a replacement pedestrian gate, or a full automated sliding gate with access control, call (747) 260-0589. A live person answers, day or night, and we’ll give you a straight answer about schedule and scope.
What Our Gate Installation Service Includes
Every gate installation we do in San Fernando starts the same way: we measure the opening, check the ground, look at the power situation, and write down exactly what we’re going to build, what it will cost, and what it will look like when we’re done. No ambiguity, no allowance sheets with vague line items. Below are the six gate types we install most often for San Fernando homeowners.
Driveway Gate
A driveway gate is the full-width gate spanning your vehicle entrance, either swing or sliding depending on your setback and slope. Most San Fernando lots with a standard 12 to 16 foot driveway opening do well with a swing gate, though we’ll tell you honestly if a slide is the better engineering call. We handle the full install: post setting, gate fabrication or assembly, motor mounting, safety devices, and the final programming of your remotes and keypad.
Pedestrian Gate
A pedestrian gate is the walk-through gate beside or within a larger driveway gate, typically 36 to 48 inches wide. You need one when a full driveway gate means people squeeze through a gap or wait for a 700-pound gate to cycle every time they check the mail. We build pedestrian gates in steel, aluminum, or wood-framed designs, and we match the finish and height to the main driveway gate so the front elevation reads as one piece.
Sliding Gate
A sliding gate rolls horizontally on a track or cantilever system instead of swinging into or away from the property. It’s the right choice when a driveway slopes upward from the street or when the setback is too shallow for a swing gate’s arc. We install both ground-track slides and cantilever slides in San Fernando, and we pay particular attention to the foundation pad and the motor placement, because those two details decide how long the gate runs before it needs service.
Swing Gate
A swing gate operates on hinges and pivots open in an arc, either inward toward the house or outward toward the street. It’s the most common residential gate type in San Fernando and usually the most cost-effective when the driveway is level and there’s room for the leaf to travel. We install single and double swing gates, set the posts in concrete to the correct depth for your soil, and dial in the limit switches so the gate stops clean without slamming the stops.
Double Gate
A double gate (also called a bi-parting gate) is two leaves that meet in the middle, splitting the opening width between them. You need a double gate when your driveway opening is wide, typically 16 to 24 feet, or when you want faster cycling and reduce the visual mass of a single oversized leaf. We install paired operators, align both leaves so they close flush with no overlap gap, and set the sequencing so the secondary leaf never drags on the ground.
Security Gate
A security gate is designed and built to resist forced entry, not just define the property line. In San Fernando that usually means taller steel construction, reinforced hinge and latch hardware, anti-lift tabs on sliding gates, and a motor with a locked-gear operator rather than a free-turning actuator. We also integrate photo-eyes, edge sensors, and vehicle detection loops where the site calls for them, because a strong gate that doesn’t stop when it should is not a safe gate.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
When a San Fernando homeowner already has a gate motor brand they trust, we work with it rather than steering them toward whatever is on the truck. We install and program DoorKing operators regularly on sliding and swing gates because the brand’s 24V DC systems hold up well in our valley heat and their swing arms are simple to service years later. DoorKing gear tends to be heavier than the residential plastic-drive alternatives, and that matters when a gate is going to cycle several hundred times a week.
Ghost Controls and Mighty Mule are the two brands we most often install on medium-duty residential driveway gates, particularly when the customer wants quiet operation and a clean phone-app interface without spending on commercial hardware. Elite and LiftMaster gear shows up on heavier ornamental steel gates where the leaf weight is above the comfort range of entry-level operators. Whatever motor is already on the property or whatever spec you’re replacing, we can quote the install with the operator that actually fits the gate’s weight, frequency of use, and your access habits.
Whether you have Ghost Controls, DoorKing, Elite, Mighty Mule, or any other make already in place, we’ll give you an honest assessment of whether it can support the new gate or whether a replacement operator belongs in the written quote. We service nine major automation brands, and we don’t sell you a motor you don’t need to make the install more profitable.
BeforeAfterSigns You Need Gate Installation Right Now
- The posts are leaning more than an inch out of plumb. When a post moves, the gate hangs and drags, and every cycle puts more stress on the hinges and the motor until something fails outright. If your posts are visibly off-vertical, the fix is often a new installation with properly set piers, not another weld on the old bracket.
- The gate scrapes the driveway every time it opens. Ground contact means the hinge bearings or the post footing have worn or settled. Continuing to run the motor against that friction will burn out a new operator in under a year, which is a repair you don’t want to pay for twice.
- The motor doesn’t match the gate’s weight. A 600-pound ornamental steel leaf on a motor rated for 400 pounds will eat gearboxes. We see this in San Fernando regularly when a previous installer saved money on the operator. The honest fix is a correctly matched motor and often a fresh install of the drive assembly.
- You’re still unlocking a chain or padlock every morning. A gate that needs manual operation isn’t a security asset, it’s a chore that eventually gets left open. If you’re already spending money on cameras or an alarm system, an automated gate with a keypad and remote ties that system together at the actual entry point.
- The gate was installed without safety devices. A motorized gate without photo-eyes or edge sensors is a serious injury risk, especially with children or pets on the property. We won’t install an automated gate without proper safety devices, and if another company did, we’ll correct the installation.
Our Gate Installation Process - Step by Step
- 1
Site measure and written quote. We come out, measure the opening width and height, check the slope, identify the power source, and look at what’s under the ground where the posts will go. We then hand you a written price for the gate, the operator if it’s automated, the hardware, the concrete, and the labor. That price is fixed before work begins, not an estimate that drifts.
- 2
Post setting and foundation work. For swing gates we dig and pour the post footings to the correct depth for your soil and gate weight, usually 36 to 48 inches in San Fernando’s valley ground. For slide gates we pour a continuous reinforced pad so the track or cantilever rollers sit true. We photograph the excavation and the pour before any concrete covers the work.
- 3
Gate fabrication and hanging. We hang the gate leaf or leaves, level them, and weld or bolt all hardware to spec. Hinges get greased, the latch is adjusted, and for doubled gates we align the meeting stile so the leaves close evenly without slamming or catching.
- 4
Operator and safety device installation. We mount the motor, run the power, and install photo-eyes at the correct height, vehicle detection loops where specified, and edge sensors on the gate’s closing edge. Every limit setting is documented: we record the open and closed positions and photograph the final switch settings so a future service call doesn’t have to guess.
- 5
Programming, walk-through, and documentation. We program remotes, keypads, and any phone-app access, then walk the gate through ten full open-close cycles with you watching. You get a photo log of the entire install and a written record of every part number installed. Under Haven Standard Clause 4 (Evidence on every job), that documentation is included, not an add-on.
How Much Does Gate Installation Cost in San Fernando?
A basic single swing driveway gate with a manual latch, powder-coated steel, and no automation typically runs $2,800 to $4,200 in San Fernando, though Gate Installation pricing varies with automation and materials. Add a quality operator and safety devices, and the installed price lands between $4,500 and $7,500 depending on gate weight and motor duty. A full sliding driveway gate with a commercial-grade DoorKing operator, vehicle loop, keypad, and phone app runs $6,500 to $9,500 on most San Fernando properties. Double gates and ornamental steel designs add material and labor and can exceed $12,000 on larger custom installations.
What moves the price: the gate’s size and weight, the type of steel or aluminum, whether the site needs a new power run, the motor’s duty rating, and whether we’re demolishing and hauling the old gate. What should not move the price after the fact is the labor. We quote the job in writing before work begins, and the price you sign is the price you pay. Ask any contractor you’re considering whether their number is an estimate or a fixed written quote. If they won’t put it in writing before the first tool comes out, walk away.
Call (747) 260-0589 for a free site measure and a written quote. No obligation, no “call us for pricing” runaround. The number we hand you is the number on the invoice.
Gate Installation Near San Fernando - Our Service Area
We install gates throughout San Fernando and the surrounding San Fernando Valley, including Sylmar, Granada Hills, Panorama City, Sun Valley, Northridge, Van Nuys, Reseda, North Hollywood, and into Santa Clarita, Burbank, and Sherman Oaks. Most San Fernando installations start within a week of the signed quote, and emergency gate work is available around the clock. For readers in nearby areas, we’ve written dedicated pages on Gate Installation in Sylmar and Gate Installation in Granada Hills. See also our home page for an overview of the full service range.
Serving San Fernando, CA - Our Local Coverage Area
We’re based in the San Fernando area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in San Fernando
Gate installation is the complete process of building, hanging, and optionally automating a driveway or pedestrian gate on your property. It includes site measurement, post setting or foundation work, gate fabrication or assembly, hardware installation, motor and safety device installation if automated, and final programming and testing. We deliver the job with a written price before work starts and a full photo record when we leave.
Most standard single swing or slide gate installations finish in one full day on site, with concrete pour work done a few days ahead to allow curing. Double gates, ornamental steel, custom fabrication, and sites needing a new electrical run usually take two to three working days. We’ll give you a firm schedule in the written quote so you know when we arrive, when we finish, and when the gate is fully operational.
Most automated driveway gate installations in San Fernando run between $4,500 and $9,500, depending on gate type, material, motor selection, and site conditions. Manual gates without automation start around $2,800, and large custom sliding gates can exceed $12,000. Every quote is fixed in writing before work starts, so the price you approve is the price you pay. Call (747) 260-0589 for a free measure and quote.
Yes, we install DoorKing operators and full DoorKing-equipped gate systems throughout San Fernando. DoorKing’s 24V DC swing and slide motors are among the most reliable we install for hot-climate residential gates, and we keep their programming tools and common parts in stock. We also install Ghost Controls, Mighty Mule, Elite, LiftMaster, FAAC, BFT, Linear, and Viking systems so the quote matches the motor that’s actually right for your gate.
Yes, a live person answers (747) 260-0589 24 hours a day, seven days a week, and we dispatch for genuine emergencies like a gate that won’t close, a motor that’s jammed, or a failed hinge that leaves the property unsecured. We’ll tell you honestly over the phone whether the situation needs same-day service or whether it can be scheduled. No voicemail loop, no callback window.
Every completed gate installation is covered by our 365-Day Done Right Promise. If the installation is not right within that full year, we make it right at no additional charge, no argument and no expiration debate. Manufacturer warranties on motors and components apply separately based on the brand, and we document every part number installed so warranty claims are simple to substantiate.
Clear the area around the gate opening so we have an unobstructed workspace, which usually means moving vehicles back from the driveway and trimming any vegetation that overhangs the gate’s travel path. If a new electrical run is needed, we’ll coordinate the trenching and panel access as part of the written scope. We handle the demo and haul-away of the old gate, so you don’t need to remove anything yourself. We’ll give you a pre-install checklist with the written quote.
Schedule Your Gate Installation Service in San Fernando Today
If you need a new gate in San Fernando, get a written price before you commit to anything. Call (747) 260-0589 and we’ll schedule a free site measure, hand you a fixed written quote, and tell you exactly when the gate goes in. Same-day service is available for emergencies, and someone on our team answers the phone at any hour. We look forward to building your gate right.
Written by Adrian Vance, Owner at Vance Gate Repair San Fernando, serving San Fernando since 2014.