Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The San Fernando Owner’s Guide

Ghost Controls access control installation in San Fernando typically runs $275-$495 installed, depending on which board you have and whether the wiring harness is still intact. We stock the common Ghost Controls control boards, receivers, and keypad kits on the truck, so about 80% of access control jobs in San Fernando are finished same day. Most owners find us after the gate stops responding to the remote what they describe as “it worked yesterday” is almost always a board, a power supply, or a chewed wire, not the motor itself.

Call (747) 260-0589

The part that actually fails on Ghost Controls systems is rarely the arm or the motor. It’s the control board, the receiver, or the connection points where low voltage meets weather. In San Fernando, the temperature swings between summer heat and cool damp winter mornings are hard on circuit boards mounted inside plastic housings. If your gate opens with the manual button but not the remote, or the keypad lights up but nothing moves, you’re looking at an access control problem, not a mechanical one.

Which Ghost Controls Models This Applies To

We work on the full Ghost Controls lineup: the standard single and dual gate kits, the TSS1 and TDS1 series, the AXXP series, and the newer Gen 2 boards. The compatibility gotcha on Ghost Controls is that the Gen 1 and Gen 2 receiver modules look nearly identical from the outside, but the pin layout is different and a Gen 2 receiver on a Gen 1 board will not respond. If you’re not sure what you have, open the control box and look at the label on the main board: Gen 1 boards say “AXDP” or “AXGP” and Gen 2 boards say “AXDP-2” or “AXGP-2.” That label is the whole game when it comes to matching parts.

For OEM versus aftermarket, our honest take from years of Ghost Controls work in San Fernando: the OEM boards from Ghost Controls are consistently reliable, but you’ll also find aftermarket universal receivers that work perfectly well for about 40% less if all you need is remote range. We’ll quote both options and let you see the written price for each before you pick. If your board is more than five years old and you’re already replacing the receiver, spending a bit more on the OEM board usually saves a second service visit inside a year.

Signs Your Ghost Controls Access Control Installation Is Failing

• Remote works only from five feet away. The receiver antenna inside the control box is loose, corroded, or the receiver module itself is losing sensitivity. We see this constantly in San Fernando, often right after a wet season when moisture crept into the housing.
• Keypad takes codes but the gate won’t move. The keypad is sending signal, but the relay on the access control board is not closing. That points to a failing board or a blown output terminal, not the keypad.
• Gate opens on its own or doesn’t close all the way. A misbehaving board can send false signals to the motor, especially if it’s mounted in direct sun. Boards that overheat in San Fernando summer afternoons will do strange things.
• Humming from the control box but no movement. The capacitor on the control board is failing. Ghost Controls boards have a capacitor that gives the motor its starting punch, and when it goes, you’ll hear power but get no travel.
• Blown fuse or tripped GFCI repeatedly. That’s a wiring fault somewhere in the low-voltage run, common on San Fernando properties where older irrigation or landscape lighting wiring shares a trench or conduit with the gate power.

Before

After

Replacement Cost & What’s Included

A Ghost Controls access control board replacement in San Fernando runs $275-$395 installed. Receiver-only jobs are $180-$260. Keypad replacement, including the weatherproof housing, runs $225-$320. Full keypad-plus-receiver-plus-board jobs top out around $495, which is what you’d spend when everything in the box is original and aged out together. The price you get from us is written down before any work starts, with the part number, the labor line, and the total all on one sheet. That’s Haven Standard Clause 1: have it in writing.

Every Ghost Controls access control installation we do in San Fernando includes the same record: photo documentation of the old board before removal, the new board after installation, limit and force readings after programming, and the final written invoice with the exact part number. The 365-Day Done Right Promise covers every access control repair we complete. If the board misbehaves within a year, we come back and make it right. No argument, no fee.

DIY or Call Us?

If you’re comfortable with a multimeter, the one safe thing you can check yourself is the low-voltage fuse on the board and the power supply output at the transformer, which should read 18-22 volts AC on most Ghost Controls setups. What you should not do is start swapping boards or receivers without isolating the power. The board itself carries low voltage, but the motor terminals and the battery backup on some Ghost Controls kits can deliver a real shock, and miswiring the board terminals is the fastest way to turn a $275 repair into a $500 one.

Access control work needs the right terminal torque, the right weather seal on the housing, and a clean wiring map before you start. That’s what we do. Name what you found. Name what it costs. Name what you left behind. If you’re in San Fernando and the gate stopped listening to you, call (747) 260-0589 and we’ll come take a look, written quote in hand before any tool touches the box.

FAQs